Opis
The Ottocanali 1204 DSP, includes DSP functionality for all 8 channels, paired with Ethernet connectivity for full control and monitoring through the ArmoníaPlus. Stand-alone in corporate board rooms, or along with Powersoft’s Installation models in the largest setups, the Ottocanali 1204 DSP with Ethernet fits any venue.
Compliant with IEC 60849, the Ottocanali 1204 DSP matches the crucial requirements for sound systems for emergency purposes.
MyPowersoft services are available for this product.
Features:
Power supply
- Universal switch mode power supply up to 400VAC tolerant with Power Factor Correction
- Patented output filter with ripple cancellation network
- Low Inrush Limiting reduces AC inrush current, removing the need for expensive power sequencers
- Detachable AC mains cable with IEC C19/22.2 (16A for EU, 20 A for USA) socket
Protections
Fully protected circuit design with:
- Ac protection: shut down power supply when AC mains voltage is outside operating range
- Clip limiter: prevents severely clipped waveforms from reaching loudspeakers, while still maintaining full peak power output
- DC protection: protects against infrasonic signal at the outputs
- VHF protections: protects the loudspeakers against non audible, strong, non musical high frequency signals
- Short circuit protection: protects the amplifier from short circuit or other stressful events for the output circuits with automatic protection reset
- Long term limiter: protects the loudspeaker against steady long term RMS (non audio) signals, by reducing maximum output
- Thermal protection: output stages operating temperature up to 80 °C (176 °F)
- Temperature controlled continous variable speed fan, front to back airflow
General
- Fixed frequency switchmode output stage for high grade sound accuracy
- Compact 1 RU for reduced rack cost and space
- Light weight – for easier racking and shipping: 5-11 kg (11-24.3 lbs) depending on number of BatFormers
- Standard Phoenix connectors: analog and digital input, audio outputs, aux supply, alarms and GPIO
- Remotely switchable inputs (main and aux) per channel
Loudspeaker system configuration
- Direct drive either low impedance loads or 70V / 100V Hi-Z distributed lines
- Switchable 35Hz / 70Hz high pass filter per channel
- Built-in defeatable clip limiters for each channel
- Mixed configuratio with Lo-Z/Hi-Z systems possible
- Bridged mode low impedance per channel pair
Alarms and GPIO
- General Purpose Input/Output alarm interfaces
- dangerous DC in the output power signal
- thermal stress
- Configurable alarm contact NC/NO per channel
- Remote AUX input / MAIN input switch
- Remote ON/OFF switch
- PWS OUT connector providing up to 24VDC
Digital Signal Processing
- Analog Devices® ADAU 1702 DSP architecture
- AD/DA converter: dual 24bit @ 48 kHz Tandem® architecture, 100 dB dynamic range, per channel
- Input/output independent equalizers per channel providing PEQ, shelving IIR filters
- Delay up to 16 ms for time alignment
- Active DampingControl™ for cable compensation
- Peak and RMS limiters
Remote management
- Control and monitoring through ArmoníaPlus
- Interface available for MediaMatrix, Crestron, AMX, Q-SYS and monitoring systems
Specifications:
| GENERAL | |||
| Output power per channel | |||
| Output power per channel | 150 W @ 4 Ω | 80 W @ 8 Ω | |
| Bridge mode | 300 W @ 8 Ω | 150 W @ 16 Ω | |
| Max output voltage / current | |||
| Max unclipped output voltage @8 Ω | 37 Vpeak | ||
| Current | 15 Apeak | ||
| AC MAIN POWER | |||
| Power supply | Universal, regulated switch mode with PFC (Power Factor Correction) | ||
| Nominal power requirement | 100-240 V ±10%, 50-60 Hz | ||
| Operating voltage | 90 V – 264 V | ||
| Power consumption/current draw | |||
| Idle | 115 V: 20 W – 0.33 A | 230 V: 21.2 W – 0.36 A | |
| 1/8 of max output power @ 4 Ω | 115 V: 224 W – 1.99 A | 230 V: 223 W – 1.24 A | |
| 1/4 of max output power @ 4 Ω | 115 V: 423 W – 3.70 A | 230 V: 417 W – 2.00 A | |
| THERMAL | |||
| Operating temperature range | 0° – 35° C – 32° – 95° F | ||
| Thermal dissipation* | |||
| Idle Energy save ON | 115 V: 29.66 BTU/h – 7.48 kcal/h | 230 V: 31.71 BTU/h – 8 kcal/h | |
| 1/8 of max output power @ 4 Ω | 115 V: 252.34 BTU/h -63.64 kcal/h | 230 V: 248.93 BTU/h – 62.78 kcal/h | |
| 1/4 of max output power @ 4 Ω | 115 V: 419.41 BTU/h -105.78 kcal/h | 230 V: 398.97 BTU/h -100.62 kcal/h | |
